How to Set up Basic Cisco ASA Firewall

Before we get started let me update you that the basic cmd configurations of the ASA firewall after ASA version 8.4 are same so please don't get confused.  If  your ASA version is 8.4 or later the configuration would be almost same.

Step 1 : 

Setup the IP  configurations on the  ASA.


ciscoasa> 
ciscoasa> en
Password: 
ciscoasa# 
ciscoasa# conf t
ciscoasa(config)# hostname Cisco-ASA
Cisco-ASA(config)# int g0/0
Cisco-ASA(config-if)# description Inside Zone
Cisco-ASA(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
Cisco-ASA(config-if)# ip add 192.168.1.1 255.255.255.0
Cisco-ASA(config-if)# no sh 

Cisco-ASA(config-if)# int g0/1
Cisco-ASA(config-if)# description Outside Zone - Towards Internet
Cisco-ASA(config-if)# nameif outside
INFO: Security level for "outside" set to 0 by default.
Cisco-ASA(config-if)# ip address 4.4.4.1 255.255.255.252
Cisco-ASA(config-if)# no sh 

Cisco-ASA(config-if)# int g0/2
Cisco-ASA(config-if)# description DMZ Side
Cisco-ASA(config-if)# nameif dmz
INFO: Security level for "dmz" set to 0 by default.
Cisco-ASA(config-if)# security-level 50 
Cisco-ASA(config-if)# ip add 192.168.20.1 255.255.255.0
Cisco-ASA(config-if)# no sh

Step 2 :

Setup the DHCP Server  to be used for inside hosts.

Cisco-ASA(config)# dhcpd address 192.168.1.5-192.168.1.254 inside

!---- To define the DHCP pool.

Cisco-ASA(config)# dhcpd dns 192.168.1.2 8.8.8.8 interface inside

!---- to define primary and secondary dns.

Cisco-ASA(config)# dhcpd enable inside

!---- Enable the DHCP for  inside hosts.

We can verify that client is getting the IP settings from the DHCP.

Step 3 :

Enable the internet access for Internal and DMZ hosts.

Cisco-ASA(config)# route outside 0 0 4.4.4.2

! -----Default route towards internet. 

Cisco-ASA(config)# nat (inside,outside) after-auto source dynamic any interface
! -----Nat rule to translate the inside host to outside public ip.

 Cisco-ASA(config)# nat (dmz,outside) after-auto source dynamic any interface
! -----Nat rule to translate the dmz host to outside public ip.

The “AFTER-AUTO” keyword simply set this NAT the least preferred rule to be evaluated after Manual NAT and Auto NAT are evaluated. The reason to give it the least preference is to avoid possible conflict with other NAT rules.

Now the settings are configured properly and the internet is working from inside and dmz hosts but the inside and dmz hosts can’t ping the internet.

That’s because the ICMP inspection in the firewall is disabled by default for security reasons as there are many type of attacks that can happen using ping the most common is the smurf attach. Or we can say the denial of service attack.

Lets enable the inspection temporary . 

Cisco-ASA# sh run policy-map

!

policy-map type inspect dns migrated_dns_map_1

 parameters

  message-length maximum client auto

  message-length maximum 512

policy-map global_policy

 class inspection_default

  inspect dns migrated_dns_map_1

  inspect ftp

  inspect h323 h225

  inspect h323 ras

  inspect ip-options

  inspect netbios

  inspect rsh

  inspect rtsp

  inspect skinny 

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect tftp

  inspect sip 

  inspect xdmcp

!

Cisco-ASA#

! -----To see the default policy.

Cisco-ASA(config)# policy-map global_policy

Cisco-ASA(config-pmap)#  class inspection_default

Cisco-ASA(config-pmap-c)# inspect  icmp

Cisco-ASA(config-pmap-c)# end

ping is working fine.

  

 Step 4 :

It is important to keep saving the logs so in any accidental situation you can see in the logs what happened on that time. We can enable the logging into the ASA’s buffer memory. We can set the log size to 512 MB or even more and the older logs are deleted automatically step by step. We can set the logging level to “Debugging” which records everything in detailed level. Make sure that the  time and date is configured correctly.

Cisco-ASA# clock  set 4:24:00 15 july 2017
Cisco-ASA(config)# clock timezone EST -5
Cisco-ASA(config)# clock summer-time EST recurring
Cisco-ASA(config)# logging buffer-size 512000
Cisco-ASA(config)# logging buffered debugging

To view logs, issue command “show logging”

If there is any question or issue  please write in the comment or send me email on

" Babararshad786@gmail.com "